What's your rule of thumb for changing COAL?

[Dougfirtree]

When you're working with load data that has a different COAL than you'd like to use, what's your rule of thumb for adjusting where you start with powder charges (or where max is apt to be)? In other words, if the load data is based on a 2.73" COAL and you'd like to use 2.8", how do you alter the powder charge for start/max loads? I feel like I'm generally able to look at different sources and make an educated guess about a safe place to start, but I'm wondering if you have a more concrete formula, etc?

 

[grizzly63]

Don't make it harder than it has to be. Start 10% below max and move up until you are happy with accuracy or you hit pressure signs. Make sure your mag and chamber will accept 2.8 first.

 

[Dougfirtree]

Don't make it harder than it has to be. Start 10% below max and move up until you are happy with accuracy or you hit pressure signs. Make sure your mag and chamber will accept 2.8 first.

Understood. But my question is, 'how do you determine what max is if you're changing the COAL from the data (since COAL affects pressure)?'

 

[cgasner1]

Understood. But my question is, 'how do you determine what max is if you're changing the COAL from the data (since COAL affects pressure)?'

Heavy or sticky bolt or sign on the back of the brass. You may wanna do some more reading or get someone that has some experience to give you a hand. It doesn’t take much of a bump to build a lot of pressure

 

[Chingon]

If going from 2.73 to 2.8 inches, I'd start at book max. But I live life on the spicy side. Safe answer is to drop one grain from max and work your way up in hot weather.

Edit - I would also not be doing this without knowing where the lands are. If you are pushing the bullet into the lands then you might have a bad day following internet advice.

 

[cgasner1]

If going from 2.73 to 2.8 inches, I'd start at book max. But I live life on the spicy side. Safe answer is to drop one grain from max and work your way up in hot weather.

Edit - I would also not be doing this without knowing where the lands are. If you are pushing the bullet into the lands then you might have a bad day following internet advice.

Even knowing where your lans are if your playing with these high bc bullets I’d recommend getting the tools to measure the o dive on the bullet and not just the tip so your getting a accurate measurement

 

[brockel]

I pay zero attention to book COAL. Kiss the lands and back off a tad or load to fit mag. Work up to pressure signs. Book data is just guidelines not rules

 

[Dougfirtree]

I pay zero attention to book COAL. Kiss the lands and back off a tad or load to fit mag. Work up to pressure signs. Book data is just guidelines not rules

Yeah, this is what I’d like to learn more about and get more comfortable with. And it’s more or less what I do, but it still helps to have confidence in where the window of safe powder charges is for the COAL you are using. Which is going to be different from the range in the published data that has a different COAL. So you can make an educated decision about what charge to start with. That was the crux of my question; whether there are formulas/rules of thumb for estimating that.

 

[Dougfirtree]

I pay zero attention to book COAL. Kiss the lands and back off a tad or load to fit mag. Work up to pressure signs. Book data is just guidelines not rules

Or to say it more concisely, work up to pressure signs from where? And how did you determine that starting charge?

 

[Dougfirtree]

Heavy or sticky bolt or sign on the back of the brass. You may wanna do some more reading or get someone that has some experience to give you a hand. It doesn’t take much of a bump to build a lot of pressure

Yeah, this I understand. I’ve been reloading for years (though I genuinely appreciate the concern). I think I didn’t describe my question very well. See my responses to Brockel above.

 

[N2TRKYS]

I use Nosler’s tested COAL in their data. I always start at a grain or half a grain below their listed max charge. I have no idea the distance to my lands and do not care how far they are. I don’t do seating depth tests. I’ve never had a reason to. I also have zero desire to ever touch the lands with my seating depth.

 

[brockel]

Or to say it more concisely, work up to pressure signs from where? And how did you determine that starting charge?

I do things different than most. I start 2 grains below max. Say book max says 60 grains. I load one at 58,59,60,61. If 61 doesn’t show pressure I’ll load one at 62. Then once I find pressure I back off a grain and load 3. If those 3 show potential I load 10 and see what it will do. I don’t play with seating depths or powder charges. If the load doesn’t shoot this way I switch powders or bullet. Just how I do things.

 

[sclancy27]

I just load to max mag length and start a grain or 2 under and work up.

So, if book max is 43 gr.

Load 2 @ 41, load 2 @ 41.5 etc. Until I get to 43 gr. I shoot them for a group. If the group is good and I find a velocity I like w/o pressure I load up a bunch and move on with my life.

 

[Drake4]

I pay zero attention to book COAL. Kiss the lands and back off a tad or load to fit mag. Work up to pressure signs. Book data is just guidelines not rules

This