What are you currently reloading?

[Nwernig]

Working up a new load for my son's 6.5PRC for a cow elk hunt. Going to see if the Barnes lrx or Hornady CX shoot better. Had bad groups with H1000 but am liking what I am seeing with H4831sc

 

[brockel]

6prc also seems to like 108 eldms. This is shots 7,8,9 down the barrel.

 

[psinclair]

3rd barrel for this rig. Bartlein 1-7.7” 5R@22”

 

[Wind Gypsy]

View attachment 380690View attachment 3806913rd barrel for this rig. Bartlein 1-7.7” 5R@22”

Standard SAAMI chamber or is it setup with a little less freebore to keep 105s closer to lands?

 

[xebadir]

Working up my 280AI load - had a slight tangent to get my reloading bench reorganized along with the garage that has held me up, along with ridiculous heat making it uncomfortable to work out there. Much cleaner organization that I'll have to get a photo of at some point.

Tested out my new RCBS bench primer tonight and quickly got 50 cases done of the Peterson brass. Still dialing it in, but beats the heck out of a hand primer.

Tomorrow I'll run the 3-shot ladder and seat so I can hit the range and get moving.

 

[psinclair]

Standard SAAMI chamber or is it setup with a little less freebore to keep 105s closer to lands?

.169 free bore. In most of my testing with Berger Hybrids (in all calibers), I've found them to be not jump sensitive. They also have worked very well for killing big game animals.

 

[turbobrick]

Mmm... obscure quarterbore

@Sheltowee, just for your quarterbore interest. The MGM barrel showed up, loaded some 87gn TNTs with Lil Gun and H335. Both shot great, no pressure signs yet, and velocity out of the 18" barrel is even higher than I'd hoped.

 

[xebadir]

Still working on my 280AI loads. Have benched the plans around H4831SC with the 160AB due to low velocities within what I can get into a case, and loaded up a ladder test set of both RL23 and IMR4350 to see if we can do any better.

 

[xebadir]

Finally got a shooter. RL23 is netting me a nice 2850 FPS at 56 gr with a 160gr AB, no pressure signs that I can see. Knew I was onto something when the first 3 shots stacked on target. Next onto dialing around there for a final number.

 

[Caseknife]

Decapped and tumbled a bunch of brass. 223AI, 257AI, 6.5CM, 7BR, 22-250

 

[Potsie]

Loaded up 30 125 HHT for my 6.5 PRC. Used 10 to verify speeds and drops - somehow picked up another 30 fps on the third firing on these brass. SD/ED shrunk as well. I’ve got verified drops out to 700, but won’t hunt that far out.

Also ran a ladder to find pressure signs in the .22-250 using 77 gr TMK and H4350.

 

[gle3105]

I’d post all the stuff I reload and methods but I’m afraid the post file size would be too big and crash the server.

 

[std7mag]

I'll be practicing with my Traditions 45 caliber inline later today.
So I'll be handloading for every shot.

Trying out different bullets and sabots.

 

[gle3105]

STD7MAG, I’ll be at the range benching ml’s. ( I’ve built many sml’s) .
Shooting tiny groups. Adjacent seasonal type hunting shooters will be patterning their centerfire pieces.
Upon them looking at my targets and seeing me push a bullet down the barrel the conversation starts.
I do inform them that I only shoot “handloads” out of this gun.

Some get it, some don’t.
Lol

 

[X13]

Before my daughter was born I stumbled into a deal I couldn't refuse and bought a Remington Model Seven .243 Win as her future first deer rifle. A couple years later with another kid on the horizon I decided that in the name of fairness he deserved a rifle as well. After much debate and deliberation, instead of buying new I had one of grandpa's guns, a Remington Model Seven .223 Rem, rebarrelled to a 18" threaded 1/7 twist Shaw .223AI with the hope of shooting heavy 75+ grain bullets for short range deer hunting. I did their barrel break in process a few weeks ago and headed to the reloading bench.

Spoiler alert....a new rifle is wearing the crown as the most accurate in the safe.

IMR 8208 XBR got the nod as the first powder and Sierra 77 gr. TMKs as the bullet. The gunsmith that did the barrel install, chamber, and magazine set it up with 2.400 OAL rounds in mind so I loaded a few of those up but didn't reliably feed. I seated them deeper to 2.365 OAL and that solved the issues.

A new scope, some zeroing rounds in the center, then 7 loads 3-rounds each. All ended sub-MOA with velocities from around 2450 to a bit over 2700.



My best was the second fastest/hottest I loaded, a bit over the Sierra book max. Can be seen there in the top center and below. The hottest load had slight primer flattening and worse cratering than the rest. They all had some degree of minor primer cratering, even the bottom end loads, assume thats a firing pin thing. No other pressure signs.



I loaded a few more of those the next day and got similar results.

 

[millerkiller77]

Decapped and tumbled a bunch of brass. 223AI, 257AI, 6.5CM, 7BR, 22-250View attachment 384722

Do you tumble them together and then hand sort by headstamp?

 

[Caseknife]

Do you tumble them together and then hand sort by headstamp?

Yep, that is why they are all pretty distinctive. Don't want to do that with similar cases. Each cartridge was a single headstamp also.

 

[millerkiller77]

Loaded up 30 125 HHT for my 6.5 PRC. Used 10 to verify speeds and drops - somehow picked up another 30 fps on the third firing on these brass. SD/ED shrunk as well. I’ve got verified drops out to 700, but won’t hunt that far out.

Also ran a ladder to find pressure signs in the .22-250 using 77 gr TMK and H4350.

What speed are you getting with the 77TMK in the 22-250?

 

[Sheltowee]

Big brother, little brother. Some 257PRC hunting loads and a 25PRC ladder test, both with Hammer HHT 127gr.

 

[Potsie]

What speed are you getting with the 77TMK in the 22-250?

Hit pressure at 37.0 gr of H4350 and had 2990 on the chrono.

Will likely back off a bit and shoot a group of 10 at 36.0 and 36.5 gr to see what groups best.

This is also through a chopped and threaded 18” barrel. I’m sure if it was factory length I could push into the 3100 range.