Christensen Arms Mesa first blush evaluation

  • Thread starter Deleted member 20812
  • Start date
I did some playing today to evaluate a couple of things.

1) number of fouling shots on a clean bore
2) how different shooting positions affect POI

On a clean bore, this rifle needs 2-3 rounds to settle. I’ve had a couple that didn’t need any. Some needed 5-6.

B3531198-514F-4768-ADA2-A75FFF2854FF.jpegB41CEE5E-909B-4205-A2DA-723B62075422.jpeg87810817-684D-4E71-9673-849EC36600E2.jpeg

The circled rounds were shots I could feel an obvious difference in how I shouldered the rifle. I got lazy on these two, and knew right away.

It appears either a free hold (off hand under the butt) or holding the off hand over the scope are the two most consistent ways to shoot this rifle.

Next step is to load a few more and check if cheek pressure affects POI at all. Then zero. Then kill elk.
 
Today I shot prone off a front bag to see what changes in form did to POI.

Disclaimer. Sandbag was a little low, which was actually an interesting variable. I struggled to really get the gun shouldered like I wanted.

The rounds in the purple circle were the ones where I really got a good consistent shoulder mount and good firm pressure to the rear. This is also the same POI as shooting from the bench.

The shots to the left were induced with thumb pressure on the side of the pistol grip.

The high shots were a result of weak pressure to the rear and/or a shoulder mount that wasn’t really “on”.

The two hammers were last just to check POI relative to the Sierra BT loads.

Time to clean good, check zero with hammers, and check drops. I haven’t checked on any shift in POI when alternating hammers and Sierras. 8DDB8FC0-A6B6-4BEB-B10D-49A6AADD464D.jpeg
 
Finally got to really stretch the legs on this rifle today.

68 degrees
Breezy - estimated 12-15 mph, probably more like 10-12 based on drift

CCI 250
71 grains RL16
Peterson brass (5th loading)
166 grain Hammer Hunter

All shots prone off front and rear bag.

I started with a clean bore. At distance it was interesting to watch it settle in. First group of four at 350 was about 6”. Second group was about 4” with the last three fairly tight.

This was 450. I dialed 4.25 MOA (Hornady app told me 3.99 but I didn’t have my readers on when I dialed).

C7C41459-D0D6-44AE-AE9A-9BC50AE9A8F8.jpeg0C8404DB-7C16-4649-A90A-5413D77A3766.jpeg

I’m not doing cartwheels, but I’m happy with this. 450-500 is as far as I’m interested in shooting under the best of conditions. This is a solid MOA rifle/load combo.

The Leupy dials like it should. This should be sufficient for now until my OCD compels me to try H4831 or a light crimp.
 
what kind of numbers is that load producing? Why not a light crimp?

My 300 loves the 180s with a stout bit of RL26 and a light crimp...I need to back it off as it starts to express pressure in the heat.
3325 fps.

I’ll try that first. I intended to this year but never got around to borrowing a Lee FCD. I expect I’ll be pretty happy with this load when I do that.
 
I’ve got monkey arms and a giraffe neck so have a 14 3/4” LOP. Just something I’ve learned over the years to make it more comfortable for shooting.

So I look for rifles with easy ability to add spacers.
 
Finally got to really stretch the legs on this rifle today.

68 degrees
Breezy - estimated 12-15 mph, probably more like 10-12 based on drift

CCI 250
71 grains RL16
Peterson brass (5th loading)
166 grain Hammer Hunter

All shots prone off front and rear bag.

I started with a clean bore. At distance it was interesting to watch it settle in. First group of four at 350 was about 6”. Second group was about 4” with the last three fairly tight.

This was 450. I dialed 4.25 MOA (Hornady app told me 3.99 but I didn’t have my readers on when I dialed).

View attachment 241712View attachment 241713

I’m not doing cartwheels, but I’m happy with this. 450-500 is as far as I’m interested in shooting under the best of conditions. This is a solid MOA rifle/load combo.

The Leupy dials like it should. This should be sufficient for now until my OCD compels me to try H4831 or a light crimp.
Almost minute of bocce ball at 450 will get it done...interested to see the unbraked results.
 
Sitka Gear Turkey Tool Belt

Latest posts

Forum statistics

Threads
110,805
Messages
1,935,061
Members
34,883
Latest member
clamwc
Back
Top