Leupold CDS

Redmt

Well-known member
Joined
Feb 12, 2021
Messages
4,489
Location
San Antonio Valley California
I'm thinking about having a CDS turret made for my VX-3 4-14 scope. It's on a Ruger #1 6.5 Creedmoor. I seriously doubt I'll ever take a hunting shot over 400-450 yds. It's included with the scope so there's no cost, but is it worth the trouble to use or just better to estimate bullet drop.
 
I'm thinking about having a CDS turret made for my VX-3 4-14 scope. It's on a Ruger #1 6.5 Creedmoor. I seriously doubt I'll ever take a hunting shot over 400-450 yds. It's included with the scope so there's no cost, but is it worth the trouble to use or just better to estimate bullet drop.

There shouldn't be any estimating with any of this stuff....
 
If your only ever going to use that one combination, sure go for it.
Ok, here's my thoughts. It's the load you helped me develop. Being a 6.5 I figured my kill range is limited, plus I don't see any reason to change bullets, and I only hunt on familiar property. I'm not big on Gizmo's and doo-dads. Would I need to range my shots first? I don't sit and wait hunt, it's more of a shot of opportunity.
 
I'm thinking about having a CDS turret made for my VX-3 4-14 scope. It's on a Ruger #1 6.5 Creedmoor. I seriously doubt I'll ever take a hunting shot over 400-450 yds. It's included with the scope so there's no cost, but is it worth the trouble to use or just better to estimate bullet drop.

A yardage turret is the easy button, but yes, you need to know the distance to the intended target.

IMG_1608 (Small).JPG
 
Ok, here's my thoughts. It's the load you helped me develop. Being a 6.5 I figured my kill range is limited, plus I don't see any reason to change bullets, and I only hunt on familiar property. I'm not big on Gizmo's and doo-dads. Would I need to range my shots first? I don't sit and wait hunt, it's more of a shot of opportunity.
Range, dial, & shoot. It will get you close enough if you gave them good data for the dial.
 
It is more than worth it. I think they wanted to know bullet type, what grain bullet, approx. what the elevation of where you are hunting.
 
For instance, I have a Ridgeline I've taken a lot of game off of. It runs from 215 yds to 260yds with about 60' elevation change. When you set the dial how close do you have to be for yardage?View attachment 406292
Set it at 225 and you would’ve fine there is likley less than an inch difference in that short of a distance. I would just verify, but for a hog there is a lot of room for error in its kill zone.
 
Or just use the MOA turret and get your velocity and BC of your bullet and develop the drop chart with that load. Same system just different measurements MOA vs Yards.
 
Set it at 225 and you would’ve fine there is likley less than an inch difference in that short of a distance. I would just verify, but for a hog there is a lot of room for error in its kill zone.
Hogs are easy. Less than 200 yds it goes in the ear. Over 200 I put it just behind the front shoulder about 1/3 way down from the top line. All have been a single shot drop up to 275 lbs.
 
Hogs are easy. Less than 200 yds it goes in the ear. Over 200 I put it just behind the front shoulder about 1/3 way down from the top line. All have been a single shot drop up to 275 lbs.
Dang, I need to be asking you how to vector distance.
;)
 
Thinking about it, there's no reason not to order it. I can always take it off . I guess I just needed some input for whether it's worth any hassle. General opinion says it's a good idea. Thanks for all the input.
 
Not quite sure I understand what you mean?

I took your question as "Do I need to figure our how this stuff works or should I just estimate and call it good?"

No, you shouldn't estimate. You need to spend some time messing with a ballistics calculator to get a grasp on what you're trying to do
 

Forum statistics

Threads
118,853
Messages
2,209,096
Members
38,678
Latest member
jiangxililiangbin
Back
Top