Here's a copy and paste off an old thread of mine. I'm not an expert by any means, but I'm getting better. I'll add some new comments in bold.
The #1 tip I would give on caping the head out is to bring a small sharp knife. My regular Gerber was too big, although I was able to get it done, a smaller knife (maybe 3" long and 3/4" wide) would have been easier, especially on the eyes and scent gland right in front of the eye.
(I now carry a small caping knife with me, one of those ones you get for joining the RMEF, it makes the job a lot easier)
The #2 tip I would give on caping would be to go ahead and try it, it really isn't that hard and it is AMAZING how much easier it is to deal with the head when it isn't attached to the cape. We didn't saw the skull plate off, but we probably lost 10lbs just by being able to cut out the entire tongue and some more meat off the back of the neck that we couldn't get too until I caped out the head. Just having the 35lb head and the 45lb cape separated makes it way less awkward to try to carry.
The tips that the guide gave me were to start out around the eyes and get as far as you can all the way around them. Just put your knife in under the eyelid and start working on it. You can get a good ways all around the eye and that keeps you from cutting the eyelid when you are working the rest of the head. I nicked the eyelid a couple times because when I was going through the opening to get to the scent gland and open everything else up around it the knife was so wide that it nicked the eyelid. A smaller knife wouldn't have had that problem.
Next tip was to get your knife down inside the scent gland in front of the eye as far as you can and then work your way out just like you did on the eye. This is where a smaller knife really would help out because my knife was so wide when I stuck it down deep into the scent gland (tear duct) the side of the knife cut into the side of the scent gland a little. My friends taxidermist said it was still okay the way I did it and he could make it work, but a smaller knife would have done a better job and been alot easier. When you are done you should have about a 5" X 3" area around the eyes and scent gland where the hide is completely free of the skull. When you are caping the head instead of struggling when you get to the eyes, now you are home free.
Last tip the guide gave me was to get as close to the teeth as possible when skinning out the mouth. That was actually pretty easy and I didn't have the problems using the larger knife that I had with the eyes and the scent glands. I worked my way up from the front of the mouth and got quite a way back all the way to where I hooked up to where I had done my work on the eyes before I stopped from the mouth. That was probably the easiest part out of all of it.
I don't start with the eyes and scent glands anymore. I just start at the mouth and start working my way back. This last bull I got the tear ducts out intact without making any cuts in the hide. Make sure you keep the cut as close to the bone as possible on the nose, you should be able to get that out pretty much intact too without cutting the nostrils.
The antler burrs were the last part I did, making the Y cut up the back of the neck to the base of the burrs. I actually started at the burr and as hard as I could cut down from the burr to make the top of the Y on each side. A strong sharp knife is really important here as you need to make that cut in one cut and not have to come back and saw on it. Next I went around the entire base of each antler burr, moving the longer hair out of the way and really making sure I had a deep cut all the way through the hide to the pedicle all the way around the burr. Then I started working around the base of each antler making sure I was cutting deep enough to be going all the way to the bone. Here is another place where a smaller knife would have probably helped, but it needs to be a sturdy knife as there is a lot of bending and pressure applied. I think you would break a Havalon knife blade pretty quick on that part.
That's about as good as I can describe it without taking a video while I'm doing it. The tips on starting at the eyes, scent glands and mouth were new to me and really made it less daunting. Once we had it caped it was much easier to deal with the cape as well since we stayed out for the rest of the week we just put the cape in a cooler and kept it on ice and didn't have to worry about it.
We tube the front legs at the knees instead of cutting down the back side of them as well. That way if you end up with some of the floor pedestal mounts you for sure have enough hide and you don't mess up on a errant cut down the side of the leg or anything like that.
I'm going to start caping all the animals I shoot even if I don't plan to mount them as it will be good practice and you can always sell the cape or trade it to your taxidermist for discounts or at least some good faith. You might not ever want to mount a raghorn bull, but there are plenty of folks that may and often those are the guys that may have butchered the cape on their bull and need one.
Hope that helps a little.
Nathan