Cold Bore shot way off

nrpate05

Well-known member
Joined
Jan 5, 2015
Messages
2,218
Hey all, thought I’d throw this out to the pros on here. The last couple times I’ve shot my 25-06, the first cold bore shot is way off. In the picture below you’ll see what I mean. The subsequent shots are decent and are grouping how this rifle usually groups. Curious what’s going on. Point of aim is the lower left corner of the red square. My internet research says a bedding issue? Thought??
 

Attachments

  • IMG_4372.jpeg
    IMG_4372.jpeg
    1.3 MB · Views: 106
How long has this been happening? Approximately how many rounds have been fired?

If you shoot a second group is the first shot drastically off as well?

As Elk Antlers asked is it a clean bore each time?
 
I have a Marlin 4570, an actual Marlin. Anyway, the first shot cold is always 5" high, but only when cold. It's perfectly straight up and down 5".I tried everything, multiple loads and bullets. Clean fouled everything. Nothing helped. It's a lever gun, so bedding is not an issue. What I did was sight it in to the first shot; it takes all day to sight in, shoot, let cool for two hours, and shoot again. It will shoot a cloverleaf group with the first shots and a cloverleaf after that, but 5" low. These are not low-velocity lead bullets; they're 300 gr Hornady 2500 fps loads. Seldom do I need more than one shot, but if I do, I have to aim 5" higher. It's not a big deal if I keep the shots around 200 yards.
 
You are 3/4in to the left......and the same high??? Is this intentional? Hard to say they are all off if it isn't hitting where it is supposed to be sighted in at?? Looks like about 1in group total. Move it to the center aim at the center and see what it does.
 
Stop cleaning it until hunting season is over. Clean it ONCE, polish it, then shoot it with out any adjustments until the POI stops moving.

Now shoot ONE. Compensate for that impact, wait 10 minutes and shoot another one.
 
What kind of gun? Is that error repeatable?

I've never seen a shift that bad. Had a carbon barrel that often threw cold bore a little over 1 MOA high. Some barrels that aren't stress relieved properly can walk. Bedding or something mechanical that shifts after the first shot (whether it's bedding, internal to scope, or scope mount) makes logical sense to me.
 
I have a Marlin 4570, an actual Marlin. Anyway, the first shot cold is always 5" high, but only when cold. It's perfectly straight up and down 5".I tried everything, multiple loads and bullets. Clean fouled everything. Nothing helped. It's a lever gun, so bedding is not an issue. What I did was sight it in to the first shot; it takes all day to sight in, shoot, let cool for two hours, and shoot again. It will shoot a cloverleaf group with the first shots and a cloverleaf after that, but 5" low. These are not low-velocity lead bullets; they're 300 gr Hornady 2500 fps loads. Seldom do I need more than one shot, but if I do, I have to aim 5" higher. It's not a big deal if I keep the shots around 200 yards.
This may be an issue with tension from the forend or mag tube, or both. Check that the forend isn't jammed against the end cap tenon, and that the end cap screws are easily installed without binding. For the mag tube, make sure it's not all the way against the shoulder in it's bore through the receiver face.
 
Reading through the responses a number of folks have missed seeing the round way down in the lower left corner. That is huge.
I too would expect a bedding problem and perhaps a ring or base problem to start.
What make and model of rifle?
What changed or has it always done this?
Scope make and model also rings and bases.
That has to be frustrating, I would try to resolve the variance in the 4 shot group.
Have you removed the action from the stock? Check the action screws?
If nothing else works send it to Paul P_Ham.
 
Hey all thanks for the responses. Its a Rem 700 25-06 that I bought new about 7 years ago. Probably has a few hundred rounds through it at most. I got a new Bell and Carlson stock for it which I think may be the culprit although it shot fine with it when I first put it on. I took the stock off to clean it but I can't recall if I did that prior to it grouping like this or not. Scope is a Leupold VX-5 3-15 Gen 1 in Talley Lightweight rings. The bore hasn't been cleaned - it'll throw a shot after I do that. I'm going to try to put the old stock back on and see if it keeps happening. Not sure when I'll have time to do that, but I'll report back.
 
And was the recoil lug pushed rearward against the stock when you tightened the action screws?
After doing a little research, I think this may be the culprit. Haven't heard of that being a potential issue before now. Thanks
 

Latest posts

Forum statistics

Threads
120,511
Messages
2,262,337
Members
39,138
Latest member
BPhelps
Back
Top