Sitka Gear Turkey Tool Belt

Recent content by Curvebow

  1. C

    7 PRC Feeding issues

    I have a Model 700 in 7mm Rem Mag and it only handles 2 down in the magazine with one in the chamber. Putting 3 rounds in is waaaaaay too tight to work. Its a fat cartridge penalty! I would guess the 7mm PRC to be perhaps worse since the whole case is as fat as the belt on the Rem Mag...
  2. C

    Christensen S/A Stocks

    Friendly bump for great stocks. I'd be all over the green one if I didn't already have one waiting for a rifle to put it on....
  3. C

    Make Bison Hunting Great Again

    Holy $hit, great story!! Thank you for sharing and CONGRATULATIONS!!!!
  4. C

    turkey gun red dot

    With my camo Remington 870, years back I installed a Leupold Gilmore red dot. It has worked great all these years (about 25!). I installed an improved cylinder choke tube & sighted in using foster style slugs at 25 yards. When I was happy with that, I replaced the chole tube with an...
  5. C

    SOLD-WTT Remington Model Seven Stock w/detachable magazine

    I have Model 7's but am not interested in the swap. However, listing the caliber might help you. I suspect that the gun is either a 308 or a 6.5 Creed. A place to look might be the big auction site, but Mod 7's don't pop, up real regularly. Best of luck; I too hate protruding detachable...
  6. C

    How Clean is Clean, Muzzleloaders

    I use BH 209 powder and M9ntana BH 209 bore cleaner in my Traditions Vortek Strikefire 50 cal. I scrubbed the barrel with wet patches & a brush until it was clean. Then dry patched it when I felt it was clean (from breech end gook always picks up from breech plug threads). Then I put 2...
  7. C

    Colorado corner crossing legislation proposal

    Oak - Unsure. Showing my severe political bias....
  8. C

    What's your favorite rimfire scope?

    I shoot 22LR inside during the winter at a gun club at 50 feet. The idea is to make a perfectly concentric hole in the very center ring which is slightly larger than a 22 hole. I use a CZ 457 with a Boyds At One stock (came that way). I installed a ~2 ounce trigger made by Triggers by Scar in...
  9. C

    Colorado corner crossing legislation proposal

    It goes on to say that if there is NOT owner consent and there is a fence, then mechanical means may be used to avoid stepping on the land or touching the fence. This seems to negate a lot of the prior language in the bill which seemed pretty nice until then. I agree, not likely to pass or...
  10. C

    7mm bullets

    PM sent…
  11. C

    Hi, while I have the 7mm Accubond seconds I got recently (20 shot up already), I'd be interested...

    Hi, while I have the 7mm Accubond seconds I got recently (20 shot up already), I'd be interested in 2 or more boxes of them if you see them around anywhere. 7mm 160 grain Accubonds. Thanks, KEN
  12. C

    Nosler Accubond availability????

    Randy - thanks for the update.... I paid $251 for 100 7mm 160 grain Accubond seconds on Gunbroker. Desperate times call for desperate measures....
  13. C

    Neat! Hidden Benefit of New Hearing Aids

    Do they have any hearing aids that also can deaden or noise cancel a gunshot? The answer is NO! Hearing aids use silicone type tips that go into your ear canal. These do NOT seal off your ear canal. Even if the hearing aid cuts out the sound, 95% of the noise is still going into your ear...
  14. C

    Nosler Accubond availability????

    Well, I guess I'm not alone! I did get some Hammer copper 150's and also the new Hornady CX 150's. But, while they shoot 1.25" groups, the 160 Accubonds were giving .5's! I may have to lower my expectations.... The good thing is, Hammer bullets are in stock. Order them, they ship them!
  15. C

    Nosler Accubond availability????

    I shoot 2 different 300 yard bench rest events each week and am well aware of component availability issues. I, like all others, have struggled with locating primers, powders and bullets. However, I HAVE been able to locate them, eventually (even from gougers on Gunbroker)! EXCEPT Nosler...

Forum statistics

Threads
110,812
Messages
1,935,334
Members
34,888
Latest member
Jack the bear
Back
Top